- Dual-Taper Precision Lockup
- Integrated Pin/Weld Hole (Converts 13.7″ to Rifle Length)
- Duty-Rated Construction
- Sequential Port Geometry
- Use for Recoil or Flash Mitigation
This is not just a muzzle brake — it’s a precision-engineered host platform built around a dual/nested taper alignment interface for unmatched concentricity and repeatability.
Designed from the ground up for modern rifle builds, this hybrid system pairs a high-efficiency staged brake with a thread-over flash splitter/cone module. The result? Controlled recoil, reduced muzzle rise, forward blast management, and suppressor-host-ready alignment — all in one modular ecosystem.
Purpose-built for 13.7” and 13.9” barrels, the XTS system adds +2.325” in length, bringing compliant 16” OAL when permanently attached.
This is modularity done right — engineered from inception, not added as an afterthought.
SEQUENTIAL EXPANSION PORT SYSTEM
• Smaller primary expansion port followed by a larger secondary chamber
• Staged gas release reduces harsh overpressure spikes
• Smoother recoil impulse compared to single-dump brakes
• Improved tracking during rapid strings of fire
DIRECTIONAL PORT GEOMETRY
• Tuned to counteract rearward recoil forces
• Mitigates vertical climb
• Maintains flat sight picture under rapid engagement
• Optimized for squared-up modern shooting stance
BALANCED LATERAL VENTING
• Controls recoil without excessive side blast
• More shooter-friendly than aggressive competition brakes
• Reduces discomfort in training or team environments
SUPPRESSOR-HOST INTERNAL BORE GEOMETRY
• Clean transition from muzzle crown into expansion chamber
• Minimizes abrupt gas shear
• Designed with concentric suppressor alignment philosophy
CONCENTRICITY-DRIVEN DESIGN
• Dual taper geometry ensures automatic self-centering
• Reduces reliance on thread fit alone
• Critical for suppressor-hosting applications
SURFACE-TO-SURFACE MECHANICAL ALIGNMENT
• Alignment via angled bearing surfaces
• Minimizes barrel shoulder tolerance stack issues
• Improves cross-manufacturer compatibility
REPEATABLE INDEXING
• Remove and reinstall modules with consistent orientation
• Reduces point-of-impact shift variability
SELF-TIGHTENING UNDER PRESSURE
• Gas impulse reinforces taper lock
• Reduced risk of loosening under sustained fire
THREAD-OVER ARCHITECTURE
• Slides over brake body
• Protects brake ports
• Forward blast projection capability
FLASH DISRUPTION GEOMETRY
• Captures and splits exiting gas plume
• Disrupts spherical flash signature
• Especially effective on shorter barrel setups
FORWARD CONCUSSION REDIRECTION
• Moves blast signature downrange
• Ideal for indoor ranges, vehicle operations, and team environments
DEVICE PROTECTION
• Shields brake ports from impact damage
• Acts as sacrificial exterior surface during hard use
• +2.325” overall device extension
• Designed to bring 13.7” barrels to 16” compliance when permanently attached
• Integrated pin/weld indexing hole
• Pre-engineered attachment point simplifies gunsmithing
• Clean weld finish without structural compromise
• High-strength steel construction
• Rated for sustained rapid fire
• Engineered wall thickness to support modular torque loads
• Reinforced taper interface to prevent distortion
• Optimized thread geometry for repeated module swaps
✔ True modular architecture — future-ready platform
✔ Suppressor-ready alignment baked into design
✔ Gas staging for smoother recoil impulse
✔ POI consistency when swapping modules
✔ Structural support for over-the-barrel torque loads
✔ Cleaner solution than long, inefficient flash hiders
This is not just a brake. It’s a precision alignment system designed for modern rifle builds that demand performance, compliance, and expandability.
Q: Is this compatible with suppressors?
Yes. The dual/nested taper interface is engineered for concentric alignment, making it suppressor-host ready.
Q: Does it require shims for timing?
The alignment system minimizes reliance on barrel shoulder tolerances. Final installation may depend on barrel specs.
Q: Can this be permanently attached for legal length compliance?
Yes. It includes a pre-engineered pin/weld indexing hole designed for clean permanent attachment.
Q: Will the flash splitter reduce blast to shooters beside me?
Yes. The cone module redirects concussion forward and protects brake ports.
Q: Is this suitable for rapid fire use?
Yes. Constructed from high-strength steel and engineered for sustained firing cycles.
• 13.7” and 13.9” builds
• Modern AR platform rifles
• Suppressor-host setups
• Professional training environments
• Builders wanting modular expansion capability
